A solar well pump that's too small runs all day and still leaves the tank low. One that's too big costs more than it needs to and can draw the well down faster than it recovers. Sizing one comes down to four numbers: how much water you need, how fast you need it, how high the pump has to lift it, and how much solar it takes to do the job. Here's how to work out each one.
Step 1: Work out daily water use
Start with gallons per day, not pump horsepower.
- Household: the USGS estimates each person uses about 80–100 gallons a day for indoor home uses (USGS Water Science School, checked November 2026).
- Livestock: needs rise sharply with heat. North Dakota State University Extension lists roughly 6 gallons a day for a beef cow at 40°F and about 20 gallons at 90°F, and about 11 gallons for a moderately active 1,100 lb horse at 68°F (NDSU AS1763, revised February 2026).
- Garden and irrigation: add your own figure. Drip systems vary widely by crop and soil.
Size for your hottest month, when people and animals drink the most and gardens need the most water.
Step 2: Turn gallons per day into gallons per minute
A solar-only pump moves most of its water in the middle of the day. A conservative planning figure is about 5–6 hours of strong pumping a day in summer, less in winter or on cloudy days.
Required flow (GPM) = daily gallons ÷ (pumping hours × 60)
Pumping into a storage tank is what makes solar water practical: the pump fills the tank while the sun is up, and gravity or a small pressure pump serves the house and troughs around the clock. Plan on at least two to three days of storage if you rely on solar alone.
Step 3: Calculate total dynamic head
Head is how hard the pump has to push, measured in feet of water. Total dynamic head (TDH) adds up four things:
- Pumping water level: the depth to the water while the pump is running, not the static level. Your well log or driller's report usually lists both.
- Vertical rise above ground: how much higher the tank inlet sits than the wellhead.
- Pressure: if you pump into a pressure tank, convert the cut-out pressure to feet. 1 psi ≈ 2.31 ft of water, so 50 psi ≈ 116 ft.
- Friction loss: pipe, fittings and long runs add resistance. For a quick estimate, add about 10% for short, properly sized pipe; use a friction-loss chart for long runs.
Every pump has a curve: flow goes down as head goes up. The maximum flow on a spec sheet is at very low head, and the maximum head is where flow approaches zero. Pick a pump whose curve gives your required GPM at your TDH, with some margin.
Step 4: Match the solar array
Bigger pumps need more panel wattage, and more panels also stretch pumping hours into the morning and late afternoon. Complete kits take the guesswork out of this, because the panel array is matched to the pump. For winter, cloudy climates or year-round livestock water, a hybrid pump that can switch to grid or generator power is worth considering.
Worked example
A rural home with four people and 20 beef cows, pumping to a storage tank:
- Daily water: 4 people × 90 gal = 360 gal. 20 cows × 20 gal (hot-weather figure) = 400 gal. Total ≈ 760 gal/day.
- Flow: 760 ÷ (6 h × 60) ≈ 2.1 GPM. Add margin for cloudy days and tank recovery: target 4–5 GPM.
- Head: pumping level 180 ft + tank 15 ft above the wellhead = 195 ft. Add 10% friction ≈ 215 ft TDH.
So the pump needs to deliver about 4–5 GPM at about 215 ft. A pump with a maximum head of about 290 ft or more, like the 3-inch Model A versions below, is in range; confirm the flow at 215 ft on the pump curve before ordering. If the pumping level were 300 ft, you'd step up to a higher-head model.
Hybrid solar DC/AC pump kit options
Our hybrid submersible pumps run on solar first and switch automatically to an AC source (150–240V, grid or generator) when sunlight is low. Each kit includes the pump and bifacial solar panels, and the pumps have a 5-year warranty and dry-run shutoff. Prices as of November 2026:
| Kit | Panels included | Max head (highest-head model) | Max flow (highest-flow model) | Price |
|---|---|---|---|---|
| 0.8HP Hybrid Solar DC/AC Submersible Pump Kit | 2 × 445W (890W) | 289.9 ft (Kit A) | 35.1 GPM (Kit E) | $1,399.99 |
| 1.34HP Hybrid Solar DC/AC Submersible Pump Kit | 3 × 445W (1,335W) | 326 ft (Kit A) | 40.3 GPM (Kit E) | $1,799.99–$2,099.99 |
| 1.61HP Hybrid Solar DC/AC Submersible Pump Kit | 4 × 445W (1,780W) | 391.2 ft (Kit A) | 39 GPM (Kit E) | $2,499.99 |
| 2.41HP Hybrid Solar DC/AC Submersible Pump Kit | 6 × 445W (2,670W) | 574 ft (Kit A) | 60.32 GPM (Kit E) | $3,799.99 |
Within each kit, the A model is built for depth (higher head, lower flow) and the E model for volume (more flow, lower head). Kit A in the 0.8HP, 1.34HP and 1.61HP sizes is a 3-inch pump; the other models are 4-inch, so check your well casing diameter.
See every size in Hybrid Solar AC/DC Brushless Submersible Pumps, or browse surface, DC and battery pump kits in Solar Water Pumps.
Common sizing mistakes
- Using static water level. The level drops when the pump runs. Use the pumping level.
- Forgetting pressure. Pumping straight into a 40/60 psi pressure tank adds about 140 ft of head at cut-out.
- Reading max flow and max head together. A pump can't deliver both at once. Use the curve.
- No storage. Without a tank, you only have water when the sun is shining, unless you use a hybrid pump with AC backup.
- Ignoring well yield. The pump shouldn't pull water faster than the well recharges. Your driller's report lists the yield in GPM.
FAQ
What size solar pump do I need for a 200 ft well?
It depends on your pumping level, how high you lift water above ground and whether you pump into a pressure tank. For 200 ft of total dynamic head, a pump with a maximum head comfortably above that, such as the 0.8HP Kit A (289.9 ft max) or the 1.34HP Kit A (326 ft max), is a starting point. Confirm the flow at your head on the curve.
Can a solar well pump run at night?
A solar-only pump stops when the sun goes down, so you store water in a tank. A hybrid DC/AC pump can switch to grid or generator power, and a battery-based kit can run from stored energy.
Can I use a solar pump with a pressure tank?
Yes. The pump can be controlled with a pressure switch or a float switch. Remember to add the pressure to your head calculation.
Will it pump in winter?
Yes, but with fewer daylight hours you'll get less water per day. Size your storage for winter, or use the AC backup on a hybrid pump.
Who should install it?
Pulling and setting a submersible pump is often done by a well contractor. Electrical work should follow the NEC and local code.
Send us your well depth, pumping level and daily water needs, and we'll recommend a pump and kit.